Подкомитет Заголовок подкомитета Опубликованные стандарты Стандарты, находящиеся на стадии разработки
ISO/TC 60/SC 1 Nomenclature and wormgearing 12 3
ISO/TC 60/SC 2 Gear capacity calculation 29 6
Фильтр :
Стандарт и/или проект находящийся в компетенции ISO/TC 60 Секретариата Этап ICS
Cylindrical gears for general and heavy engineering — Basic rack
95.99
Cylindrical gears for general and heavy engineering — Standard basic rack tooth profile
90.93
Cylindrical gears for general engineering and for heavy engineering — Modules and diametral pitches
95.99
Cylindrical gears for general engineering and for heavy engineering — Modules
90.93
Withdrawal of ISO/R 467-1966
95.99
Straight bevel gears for general engineering and heavy engineering — Basic rack
90.93
Straight bevel gears for general engineering and heavy engineering — Modules and diametral pitches
90.93
International gear notation — Symbols for geometrical data
95.99
Glossary of gear terms — Part 1: Geometrical definitions
95.99
Withdrawal of ISO/R 1122-1969
95.99
Cylindrical gears — ISO system of accuracy — Part 1: Definitions and allowable values of deviations relevant to corresponding flanks of gear teeth
95.99
Cylindrical gears — ISO system of flank tolerance classification — Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth
90.93
Cylindrical gears — ISO system of accuracy — Part 2: Definitions and allowable values of deviations relevant to radial composite deviations and runout information
95.99
Cylindrical gears — ISO system of flank tolerance classification — Part 2: Definitions and allowable values of double flank radial composite deviations
60.60
Parallel involute gears — ISO system of accuracy
95.99
Cylindrical gears — Information to be given to the manufacturer by the purchaser in order to obtain the gear required
95.99
Straight bevel gears — Information to be given to the manufacturer by the purchaser in order to obtain the gear required
95.99
Single-start solid (monobloc) gear hobs with axial keyway, 1 to 20 module and 1 to 20 diametral pitch — Nominal dimensions
95.99
Single-start solid (monobloc) gear hobs with tenon drive or axial keyway, 1 to 40 module — Nominal dimensions
95.99
Addendum modification of the teeth of cylindrical gears for speed-reducing and speed-increasing gear pairs
95.99
Gear hobs — Single start — Accuracy requirements
95.99
Acceptance code for gears — Part 1: Determination of airborne sound power levels emitted by gear units
95.99
Acceptance code for gear units — Part 1: Test code for airborne sound
90.93
Acceptance code for gears — Part 2: Determination of mechanical vibrations of gear units during acceptance testing
95.99
Code of inspection practice — Part 1: Inspection of corresponding flanks of gear teeth
95.99
Code of inspection practice — Part 1: Inspection of corresponding flanks of gear teeth — Technical Corrigendum 1
95.99
Code of inspection practice — Part 1: Measurement of cylindrical gear tooth flanks
95.99
Code of inspection practice — Part 1: Measurement of cylindrical gear tooth flanks
90.93
Code of inspection practice — Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash
90.92
Code of inspection practice — Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash — Technical Corrigendum 1
60.60
Code of inspection practice — Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash — Technical Corrigendum 2
60.60
Code of inspection practice — Part 2: Double Flank Radial Composite Measurements
30.60
Code of inspection practice — Part 3: Recommendations relative to gear blanks, shaft centre distance and parallelism of axes
90.93
Code of inspection practice — Part 3: Recommendations relative to gear blanks, shaft centre distance and parallelism of axes — Technical Corrigendum 1
60.60
Code of inspection practice — Part 4: Recommendations relative to surface texture and tooth contact pattern checking
90.93
Code of inspection practice — Part 4: Recommendations relative to surface texture and tooth contact pattern checking — Technical Corrigendum 1
60.60
Code of inspection practice — Part 5: Recommendations relative to evaluation of gear measuring instruments
90.93
Code of inspection practice — Part 5: Recommendations relative to evaluation of gear measuring instruments — Technical Corrigendum 1
60.60
Code of inspection practice — Part 6: Bevel gear measurement methods
90.93
Enclosed gear drives for industrial applications
95.99
Enclosed gear drives for industrial applications — Technical Corrigendum 1
95.99
Bevel gears — ISO system of accuracy
90.93
Gears — Evaluation of instruments for the measurement of individual gears
90.93
Cylindrical involute gears and gear pairs — Part 2 — Part 2: Calculation and Measurement of Tooth Thickness and Backlash
30.00
Wind turbines — Part 4: Design requirements for wind turbine gearboxes
90.92
Wind turbines — Part 4: Design requirements for wind turbine gearboxes
30.60
Wind turbines — Part 4: Design and specification of gearboxes
95.99
Wind turbines — Part 4: Design and specification of gearboxes — Technical Corrigendum 1
95.99

По запросу ничего не найдено. Пожалуйста, попробуйте изменить настройки фильтра.